Lenovo ThinkSystem SR860v2 4x Gold 6330H 24C 2.0GHz 150W/4x32GB/0GB 2,5"(16)/940-16i(4GB f)/XCC-E/4x1800W

Lenovo ThinkSystem SR860v2 4x Gold 6330H 24C 2.0GHz 150W/4x32GB/0GB 2,5"(16)/940-16i(4GB f)/XCC-E/4x1800W 7Z60A00MEA 4x Gold 6330H 24C 150W 2.0GHz 4x 32GB 2Rx4 1x 940-16i 16x AnyBay / 48 2.5" open bay; 1x 7mm S4510 480GB / 2 Open 5 / 14 (Riser 1 is x8/x8) 4x 1800W P Y Y

Machine types 7Z59 - 1-year warranty

7Z60 - 3-year warranty

7D42 - SAP HANA configurations with 3-year warranty

Form factor 4U rack.

Processor Two or four third-generation Intel Xeon Scalable processors, either Gold or Platinum level processors, with H or HL suffixes (formerly codename "Cooper Lake" or CPX6). Supports processors up to 28 cores, core speeds up to 3.9 GHz, and TDP ratings up to 250W. Two processor sockets on the system board and two processors on the Processor and Memory Expansion Tray. Six Intel Ultra Path Interconnect (UPI) links at 10.4 GT/s each. Four processors are connected in a mesh topology.

Chipset Intel C621A "Lewisburg" chipset, part of the platform codenamed "Cedar Island" (CDS)

Memory Up to 48 DIMM slots (12 DIMMs per processor). Each processor has 6 memory channels, with 2 DIMMs per channel. Lenovo TruDDR4 RDIMMs and 3DS RDIMMs are supported. 24 DIMM sockets on the system board, and an additional 24 DIMM sockets on the processor and memory expansion tray. DIMM slots are shared between standard system memory and persistent memory. DIMMs operate at up to 3200 MHz at 2 DPC.

Persistent memory Supports up to 24x Intel Optane Persistent Memory 200 Series modules installed in the DIMM slots. Persistent memory is installed in combination with system memory DIMMs. Supports App Direct mode to enhance the performance of applications such as SAP HANA.

Memory maximums

With system memory DIMMs: Up to 12TB with 48x 256GB 3DS RDIMMs and four processors (3.0TB per processor).

With Persistent Memory in AppDirect mode: Up to 18TB total memory (12TB of Persistent Memory using 24x 512GB PMMs + 6TB of system memory using 24x 256GB 3DS RDIMMs and four processors) (4.5TB per processor)

Note: Support of more than 1.125TB per processor (more than 4.5TB total for a 4-processor system) requires HL-suffix processors. These calculations include any Persistent Memory installed. See the Memory capacity of processors section for more information.

Memory protection ECC, SDDC (for x4-based memory DIMMs), ADDDC (for x4-based memory DIMMs), memory mirroring, and memory sparing.

Disk drive bays Up to 48x 2.5-inch hot-swap drive bays:

Up to 48x SAS/SATA drive bays

Up to 24x SAS/SATA + 24x NVMe drive bays

Up to 24x SAS/SATA + 24x AnyBay drive bays (support SAS or SATA or NVMe drives)

Optional two 7mm hot-swap SSD drive bays at the rear of the server, either SATA or NVMe, for OS boot or storage

Maximum internal storage

737.28TB using 48x 15.36TB 2.5-inch SAS SSDs

192TB using 24x 8TB 2.5-inch NVMe SSDs

115.2TB using 48x 2.4TB 2.5-inch HDDs

Mix of NVMe/SSDs/HDDs supported.

Storage controller

8x Onboard SATA ports (Intel VROC SATA RAID, formerly known as Intel RSTe RAID)

Up to 16x Onboard NVMe ports (includes Intel VROC NVMe RAID, with optional license for non-Intel NVMe SSDs)

NVMe Switch Adapters (no RAID) (also supports Intel VROC)

12 Gb SAS/SATA RAID adapters:

RAID 530i-8i (cacheless) supports RAID 0, 1, 10, 5, 50

RAID 530i-16i (cacheless) supports RAID 0, 1, 10

RAID 930-8i with 2GB flash-backed cache supports RAID 0, 1, 10, 5, 50, 6, 60

RAID 930-16i with 4GB flash-backed cache supports RAID 0, 1, 10, 5, 50, 6, 60

RAID 940-32i with 8GB flash-backed cache supports RAID 0, 1, 10, 5, 50, 6, 60

RAID 940-8i with 4GB or 8GB flash-backed cache supports RAID 0, 1, 10, 5, 50, 6, 60

RAID 940-16i with 4GB or 8GB flash-backed cache supports RAID 0, 1, 10, 5, 50, 6, 60

12 Gb SAS/SATA non-RAID:

430-8i or 440-8i HBAs

430-16i or 440-16i HBAs

Optical drive bays No internal optical drive.

Tape drive bays No internal backup drive.

Network interfaces Dedicated OCP 3.0 SFF slot with PCIe 3.0 x16 host interface. Supports a variety of 2-port and 4-port adapters with 1GbE, 10GbE and 25GbE network connectivity. One port can optionally be shared with the XClarity Controller (XCC) management processor for Wake-on-LAN and NC-SI support.

PCI Expansion slots

Up to 14 PCIe 3.0 slots plus an OCP 3.0 slot reserved for an Ethernet adapter. Three slots (slots 13, 14, 15) are on the system board and three slots (slots 5, 6, 7) are through a lower riser card. Slots 1, 2, 3, 4 and slots 9, 10, 11, 12 are via upper riser cards that connect to the processors on the processor and memory expansion tray. Slots 1-4 and 9-12 require 4 processors.

The slots are as follows:

Slot 1: PCIe x8 FHFL (not present if slot 2 is PCIe x16) (CPU 4)

Slot 2: PCIe x8 FHFL or PCIe x16 FHFL double-wide (CPU 4)

Slot 3: PCIe x8 FHFL (not present if slot 4 is PCIe x16) (CPU 4)

Slot 4: PCIe x8 FHFL or PCIe x16 FHFL double-wide (CPU 4)

Slot 5: PCIe x16 FHHL (CPU 2) or PCIe x8 FHHL with 2-slot riser (CPU 2)*

Slot 6: PCIe x16 FHHL (CPU 1) or PCIe x8 FHHL with 2-slot riser (CPU 1)*

Slot 7: PCIe x16 FHHL (not present if 2-slot riser is selected) (CPU 2)*

Slot 8: OCP 3.0 slot with PCIe x16 connection (CPU 2)

Slot 9: PCIe x8 FHFL (not present if slot 10 is PCIe x16) (CPU 3)

Slot 10: PCIe x8 FHFL or PCIe x16 FHFL double-wide (CPU 3)

Slot 11: PCIe x8 FHFL (not present if slot 12 is PCIe x16) (CPU 3)

Slot 12: PCIe x8 FHFL or PCIe x16 FHFL double-wide (CPU 3)

Slot 13: PCIe x16 LP (CPU 1)

Slot 14: PCIe x8 LP (CPU 1)

Slot 15: PCIe x8 LP (CPU 1)

* Slots 5, 6 and 7 are implemented using a riser. With a 3-slot riser, all slots are PCIe x16, however this riser is mutually exclusive with 8x NVMe drive connections. Alternatively, a 2-slot riser can be selected (slots 5 & 6, both PCIe x8) which allow the use of the 8x NVMe drive connections. See the System architecture section for a graphical view of the connections.

GPU support Supports up to 8x single-wide GPUs or up to 4x double-wide GPUs

Ports

Front: One VGA video port. 1x USB 3.1 G1 (5 Gb/s) port, 1x USB 2.0 port. The USB 2.0 port can be configured to support local systems management by using the XClarity Administrator mobile app on a mobile device connected via a USB cable.

Rear: Two USB 3.1 G1 (5 Gbp/s) ports, one VGA video port, one DB-9 serial port, and one RJ-45 XClarity Controller (XCC) systems management port. The serial port can be shared with the XCC for serial redirection functions.

Internal: Optional M.2 adapter in dedicated slot supporting one or two M.2 drives (for OS boot support, including hypervisor support).

Cooling

Eight N+1 redundant hot-swap 60 mm fans (all eight standard). Two additional fans connected to each of the two upper riser units. One additional fan integrated in each of the four power supplies.

Power supply Up to four hot-swap redundant AC power supplies (all 80 PLUS Platinum or Titanium certification): 750 W, 1100 W and 1800 W AC options, supporting 220 V AC. 750 W and 1100 W options also support 110V input supply. In China only, all power supply options support 240 V DC. Power supplies can be configured as N+1 or N+N.